The CLAAS 350 Baler is known for its reliability and performance, but like any piece of machinery, it can encounter issues that affect bale quality and production efficiency. If you're experiencing problems such as bales busting, net splitting, or net wrapping, this troubleshooting guide will help you identify and resolve common issues. Are you still looking for high-quality net wrap? Find it on Agzaga.com!

Why are my bales busting or breaking apart?

Possible Causes: 

• Damage to Bale from Chamber Rollers: If the chamber rollers are damaged, they can cause unnecessary pressure on the bales, resulting in busting or misshapen bales. 
• Bale Not Turning on Ejection: If the bale is not rotating properly during ejection, it may get stuck or damaged, especially on uneven surfaces. 
• Dirty Rollers: Crop residue or debris buildup on the rollers can obstruct the baling process, leading to incomplete or damaged bales. 
• Ejecting Bale on a Slope: If you're ejecting a bale on a slope or incline, gravity can cause the bale to break or roll uncontrollably. Ensure proper alignment on level ground when ejecting. 
• Rusty or Newly Painted Chamber Side Walls: These conditions can cause increased friction, leading to damage during bale formation or ejection. 
• Net Broken from Damaged Chamber Rollers: Damaged chamber rollers may snag or tear the net, which can lead to broken or incomplete bales. 

Solutions: 

• Inspect and repair or replace damaged chamber rollers. 

• Regularly clean the rollers to ensure smooth operation. 

• Avoid ejecting bales on slopes when possible or take precautions to prevent damage. 

• Remove rust and ensure the chamber side walls are smooth and well-maintained. 

Why do I have badly shaped bales or poor bale formation?

Possible Causes: 

• Bale Not Circular: Poor bale formation often leads to misshapen or irregularly sized bales. 
• Bad Crop Pick-Up: If the baler is not picking up the crop evenly, it will result in an uneven bale profile.

Solutions: 

• Adjust the crop pick-up settings to ensure even distribution of the material during baling. 

• Check for any mechanical obstructions that could be affecting the bale formation process. 

Why is the net splitting on the bale?

Possible Causes: 

• Threads Laddering: Threads being pulled out of the net or improper stitching can cause net splitting. 
• Threads Catching on Feeding Rollers: Damaged or improperly aligned feeding rollers can catch threads and cause them to break. 
• Damaged Threads in Net: Nets with damaged threads from storage or handling will fail during baling. 
• Bad Net Cut Due to Poor Tension: Poor net tension can cause the net to tear unevenly, leading to splitting. 

Solutions: 

• Inspect and replace the net if the threads are damaged or improperly stitched. 

• Ensure proper tensioning of the net and adjust feeding rollers as necessary. 

Why is my net not spreading properly?

Possible Causes: 

• Bad Bale Shape Density: If the bale shape or density is uneven, the net may not spread evenly around the bale. 
• Poor Net Tension: Insufficient net tension can cause the net to fail to spread properly. 
• Brake Bar Spring Needs Adjusting: If the brake bar spring is not set correctly, it may affect the net tension. 
• Feeding Roller Setting Adjustment Needed: Incorrect feeding roller settings can prevent the net from spreading evenly. 
• Net Not Feeding Through Enough Tension Bars: Ensure that the net is properly feeding through all the tension bars in the baler. 

Solutions: 

• Adjust the brake bar spring and feeding roller settings to optimize net tension. 

• Ensure the net is feeding properly through all tension bars and rollers. 

Why am I having issues with my net wrapping on the feeding roller?

Possible Causes: 

• Threads Catching on Feeding Roller: Improperly aligned threads or debris on the feeding roller can cause the net to wrap around it. 
• Bad Net Cut Due to Poor Tension: Uneven net cuts can lead to wrapping issues. 
• Dirty Net Feeding Plate: A dirty or contaminated feeding plate can interfere with proper net feeding. 
• Rusty or Damaged Brake Bar: Rust or damage to the brake bar can cause the net to snag and wrap around rollers. 
• Feeding Rollers Contaminated with Moisture or Crop Residue: Moisture or debris can cause the net to stick to the rollers. 

Solutions: 

• Clean the feeding rollers and feeding plate to remove any moisture or debris. 

• Check and replace any rusty or damaged parts, especially the brake bar. 

Why is my net breaking when feeding?

Possible Causes: 

• Bad Bale Shape and Density: Poorly formed bales can exert uneven pressure on the net, causing it to break. 
• Excess Net Tension: Excessive tension can cause the net to snap during feeding. 
• Brake Bar Spring Needs Adjusting: The brake bar spring may be too tight or too loose, causing net breakage. 
• Brake Bar Not Required When Net Roll is Full: When the net roll is full, the brake bar may not be necessary and can cause excess tension. 
• Net Feeding Through Too Many Tension Bars: Over-complicating the tensioning process can cause additional stress on the net. 
• Roll Core Jammed in Net Box: A jammed roll core can stop the net from feeding properly, resulting in breakage. 
• Net Drive Belt on Wrong Pulley: Incorrect drive belt positioning can affect net feeding. 

Solutions: 

• Adjust the net tension to avoid excessive pressure on the net. 

• Check and adjust the brake bar spring for optimal performance. 

• Ensure the roll core is not jammed, and the drive belt is on the correct pulley. 

Final Tips: 

• Regular Maintenance: Regularly inspect and clean all components, including rollers, feeding plates, and tension bars. 
• Proper Storage: Store nets in a dry, protected environment to avoid damage from moisture or UV exposure. 
• Alignment: Ensure all mechanical parts are properly aligned to prevent net damage or malfunctions. 

By addressing these common issues, you can ensure your CLAAS 350 Baler operates smoothly and continues to produce high-quality bales. Proper maintenance and timely adjustments will help you avoid downtime and maximize the productivity of your baler. 

Need net wrap and baler parts? Find them on Agzaga.com!